Presseberichte und -bilder » /]Cheap Sevilla Hoodies[/url] ,000 per ye

Question: 1

In severe refinery services which type of pipe is normally used?

A. Cast
B. Machined
C. Seamless
D. Welded

Answer: C


Question: 2

Pressure applied inside a pipe creates stresses in the pipe wall. These stresses are highest on which weld orientation?

A. Circumferential weld
B. Longitudinal weld
C. 30 degree mitered weld
D. All are about the same


Answer: B


Question: 3

Which of the following is not an acceptable method for establishing the piping corrosion rate in a new service?

A. Owner's experience
B. Inspect the piping system within 3 months of operation
C. Corrosion data from trade journal
D. Corrosion data from phone discussion with a consultant corrosion engineer.


Answer: D


Question: 4

Per B31.3 Coke Jersey , how much RT is conducted on circumferential welds of a pipe in Normal Service?

A. 0%
B. 5%
C. 10%
D. 100%
E. Depends on flange class


Answer: B


Question: 5

For welded pipe, the normal thickness undertolerance is:

A. -0.00 inch.
B. -0.01 inch.
C. -0.0125 inch.
D. -12.5% of the specified wall thickness.


Answer: B


Question: 6

When qualifying a weld procedure the essential variables must:

A. be recorded on only the PQR.
B. be recorded on only the WPS.
C. be recorded on both the WPS and PQR.
D. be recorded on both the WPS and WPQ


Answer: C


Question: 7

A pipe has a thickness designation of "40S". What does the "S" mean?

A. Schedule
B. Seamless
C. Stainless steel
D. Steel


Answer: C


Question: 8

A hydrotest is being conducted on an underground line as a substitute for the external inspection.
The test pressure is 200 psig. At the end of the test, the pressure must be at least:


A. 100 psig.
B. 175 psig.
C. 190 psig.
D. 195 psig.
E. 200 psig.


Answer: C


Question: 9

Determine the maximum allowed pressure for a Class 300 flange that has a design temperature of 950 掳F. The flange material is ASTM A217 gr.C12.


A. 50 psig
B. 375 psig
C. 750 psig
D. Not allowed - temperature is too high for this material


Answer: B


Question: 10

An 8 NPS pipe is being replaced with A106 gr. B material. The pipe retirement thickness is 0.218" and the corrosion allowance is 0.125". What'is the minimum thickness of pipe that could be ordered after adjusting for mill-tolerance?

A. 0.218"
B. 0.249"
C. 0.343"
D. 0.353"
E. 0.392"


Answer: E


Question: 11

A welder is being qualified by RT on a 0.600" plate using the SMAW process. What is the maximum allowed elongated slag inclusion for this qualifying test?


A. 0.125"
B. 0.200"
C. 0.600"
D. 1.200"


Answer: B


Question: 12

During the evaluation of a radiograph, the density at the 101 is 3.0. What is the minimum density allowed on this radiograph in the weld?


A. 2.00
B. 2.10
C. 2.55
D. 3.00


Answer: C

Total Views: 51Word Count: 815See All articles From Author
>Jain University Admissions and Eligibility Crieteria:

Posted by iesonline12 on May 14th Ciro Immobile Jersey , 2018


When it comes down to choosing a reliable educational institute, most of us tend to face a lot of difficulties. And, it is quite obvious as it’s a matter of an individual’s career. If you’re looking for a reputed university or an institute, then nothing could be better than Jain University.


Jain University is an educational hub that offers a plethora of undergraduate Beto Jersey , postgraduate and research programs in different streams, including Management, Commerce, Humanities [url=http://www.cheapsevillashop.com/

Bachelor of Arts + Bachelor of Law (B.A.L.L.B) (Hons.)- Rs. 300 Cheap Sevilla Hoodies ,000 per yearBachelor of Science + Bachelor of Laws (B.Sc. L.L.B)- Rs. 300,000 per yearBachelor of Commerce + Bachelor of Laws (L.L.B)- Rs. 300,000 per yearBachelor of Business Administration + Bachelor of Laws(B.A.L.L.B)- Rs. 300,000 per yearBachelor of Technology (B.Tech)- Rs. 160 Cheap Sevilla Shirts ,000 per yearBachelor of Science (B.Sc)- Rs. 40,500 per yearBachelor of Technology (B.Tech) (Lateral)- Rs. 160,000 per yearBachelor of Arts (BA)- Rs. 71,000 per yearBachelor of Computer Application (BCA)- Rs. 102 Cheap Sevilla Jerseys ,000 per yearBachelor of Management Studies (BMS)- Rs. 145,000 per year Jain University Admission Jain University conducts Jain Entrance Test (JET) every year for admissions to different undergraduate and postgraduate programs. Students who want to enroll themselves in Jain Univer. Cheap Jerseys Cheap Jerseys Wholesale Cheap Jerseys China Cheap Jerseys Wholesale Cheap Jerseys Online Wholesale Jerseys Free Shipping Wholesale NHL Jerseys Cheap Wholesale NFL Jerseys Free Shipping Wholesale NCAA Jerseys Cheap Wholesale College Basketball Jerseys